SPEC CPU2006 Platform Settings for HP Proliant AMD-based systems

Operating System Tuning Parameters

OS Tuning

submit= MYMASK=`printf '0x%x' \$((1<<\$SPECCOPYNUM))`; /usr/bin/taskset \$MYMASK $command

When running multiple copies of benchmarks, the SPEC config file feature submit is sometimes used to cause individual jobs to be bound to specific processors. This specific submit command is used for Linux. The description of the elements of the command are:

Using numactl to bind processes and memory to cores

For multi-copy runs or single copy runs on systems with multiple sockets, it is advantageous to bind a process to a particular core. Otherwise, the OS may arbitrarily move your process from one core to another. This can effect performance. To help, SPEC allows the use of a "submit" command where users can specify a utility to use to bind processes. We have found the utility 'numactl' to be the best choice.

numactl runs processes with a specific NUMA scheduling or memory placement policy. The policy is set for a command and inherited by all of its children. The numactl flag "--physcpubind" specifies which core(s) to bind the process. "-l" instructs numactl to keep a process memory on the local node while "-m" specifies which node(s) to place a process memory. For full details on using numactl, please refer to your Linux documentation, 'man numactl'

numactl --interleave=all "runspec command"

Launching a process with numactl --interleave=all sets the memory interleave policy so that memory will be allocated using round robin on nodes. When memory cannot be allocated on the current interleave target fall back to other nodes.

Transparent Huge Pages

On RedHat EL 6 and later, Transparent Hugepages increase the memory page size from 4 kilobytes to 2 megabytes. Transparent Hugepages provide significant performance advantages on systems with highly contended resources and large memory workloads. If memory utilization is too high or memory is badly fragmented which prevents hugepages being allocated, the kernel will assign smaller 4k pages instead. Hugepages are used by default if /sys/kernel/mm/redhat_transparent_hugepage/enabled is set to always.

ulimit -s [n | unlimited] (Linux)

Sets the stack size to n kbytes, or unlimited to allow the stack size to grow without limit.

KMP_STACKSIZE=integer[B|K|M|G|T] (Linux)

Sets the number of bytes to allocate for each parallel thread to use as its private stack. Use the optional suffix B, K, M, G, or T, to specify bytes, kilobytes, megabytes, gigabytes, or terabytes. The default setting is 2M on IA32 and 4M on IA64.

KMP_AFFINITY=physical,n (Linux)

Assigns threads to consecutive physical processors (for example, cores), beginning at processor n. Specifies the static mapping of user threads to physical cores, beginning at processor n. For example, if a system is configured with 8 cores, and OMP_NUM_THREADS=8 and KMP_AFFINITY=physical,2 are set, then thread 0 will mapped to core 2, thread 1 will be mapped to core 3, and so on in a round-robin fashion.

OMP_NUM_THREADS=n

This Environment Variable sets the maximum number of threads to use for OpenMP* parallel regions to n if no other value is specified in the application. This environment variable applies to both -openmp and -parallel (Linux) or /Qopenmp and /Qparallel (Windows). Example syntax on a Linux system with 8 cores:
export OMP_NUM_THREADS=8
Default is the number of cores visible to the OS.

vm.max_map_count-n (Linux)

The maximum number of memory map areas a process may have. Memory map areas are used as a side-effect of calling malloc, directly by mmap and mprotect, and also when loading shared libraries.


Firmware / BIOS / Microcode Settings

Firmware Settings

One or more of the following settings may have been set. If so, the "Platform Notes" section of the report will say so; and you can read below to find out more about what these settings mean.

Power Regulator for ProLiant support (Default=HP Dynamic Power Savings Mode)

Values for this BIOS setting can be:

HP Power Profile (Default = Balanced Power and Performance):

Values for this BIOS setting can be:

Power Efficiency Mode (Default=Efficiency)

Values for this BIOS setting can be:

Dynamic Power Capping Functionality (Default = Enabled):

This BIOS option allows the user to disable the System ROM Power Calibration feature that is executed during the boot process. When disabled, the user can expect faster boot times but will not be able to enable a Dynamic Power Cap until this feature is re-enabled.

Minimum Processor Idle Power C1e State (Default = Disabled):

This BIOS option allows the enabling/disabling of a processor mechanism to allow the processor to enter a reduced power C1e state when all cores of a processor have entered a low power C-state. Enabling this feature will result in substanital power savings in most configurations.

Adjacent Sector Prefetch (Default = Enabled):

This BIOS option allows the enabling/disabling of a processor mechanism to fetch the adjacent cache line within an 128-byte sector that contains the data needed due to a cache line miss.

In some limited cases, setting this option to Disabled may improve performance. In the majority of cases, the default value of Enabled provides better performance. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Hardware Prefetch (Default = Enabled):

This BIOS option allows allows the enabling/disabling of a processor mechanism to prefetch data into the cache according to a pattern recognition algorithm.

In some limited cases, setting this option to Disabled may improve performance. In the majority of cases, the default value of Enabled provides better performance. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Data Reuse (Default = Enabled):

This BIOS option allows the enabling/disabling of the Data Reuse optimization.

Enabling this option reduces the frequency of L3 cache updates from the L1 cache. This may improve performance by reducing the internal bandwidth consumed by constantly updating L1 cache lines in the L3 cache.

Since this optimization results in more fetches to main memory, in some limited cases, setting this option to Disabled may improve performance. In the majority of cases, the default value of Enabled provides better performance. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Thermal Configuration (Default = Optimal Cooling):

This feature allows the user to select the fan cooling solution for the system. Values for this BIOS option can be:

Collaborative Power Control (Default = Enabled):

This BIOS option allows the enabling/disabling of the Processor Clocking Controll (PCC) Interface, for operating systems which support this feature. Enabling this option allows the Operating System to request processor frequency changes even when the server has the Power Regulator option configured for Dynamic Power Savings Mode.

For Operating Systems that do not support the PCC Interface or when the Power Regulator Mode is not configured for Dynamic Power Savings Mode, this option has no impact on system operation.

SATA #1 Controller (Default=Auto)

Sets the mode for the embedded controller. The values for this BIOS setting can be:

Processor Power and Utilization Monitoring (Default = Enabled):

This BIOS option allows allows the enabling/disabling of iLo4 Processor State Mode Switching and Insight Power Management Processor Utilization Monitoring.

When set to disabled, the system will also set the HP Power Regulator mode to HP Static High Performance mode and the HP Power Profile mode to Custom. This option may be useful in some environments that require absolute minimum latency.

Memory Refresh Rate (Default = 2x Refresh):

This BIOS option controls the refresh rate of the memory controller and may affect the performance and resiliency of the servers memory.

When set to 1x Refresh, the memory refresh rate will be decreased, the HP Power Regulator mode will be set to HP Static High Performance mode, and the HP Power Profile mode to Custom. This option may be useful in some environments that require absolute minimum latency.

When set to 3x Refresh, the memory refresh rate will be increased, the HP Power Regulator mode will be set to HP Static High Performance mode, and the HP Power Profile mode to Custom.

Last updated March 31st, 2014.