CPU2006 Flag Description
Fujitsu PRIMERGY RX100 S7, Intel Xeon E3-1280, 3.50 GHz

Copyright © 2006 Intel Corporation. All Rights Reserved.


Base Compiler Invocation

C benchmarks

C++ benchmarks

Fortran benchmarks

Benchmarks using both Fortran and C


Peak Compiler Invocation

C benchmarks

C++ benchmarks

Fortran benchmarks

Benchmarks using both Fortran and C


Base Portability Flags

410.bwaves

416.gamess

433.milc

434.zeusmp

435.gromacs

436.cactusADM

437.leslie3d

444.namd

447.dealII

450.soplex

453.povray

454.calculix

459.GemsFDTD

465.tonto

470.lbm

481.wrf

482.sphinx3


Peak Portability Flags

410.bwaves

416.gamess

433.milc

434.zeusmp

435.gromacs

436.cactusADM

437.leslie3d

444.namd

447.dealII

450.soplex

453.povray

454.calculix

459.GemsFDTD

465.tonto

470.lbm

481.wrf

482.sphinx3


Base Optimization Flags

C benchmarks

C++ benchmarks

Fortran benchmarks

Benchmarks using both Fortran and C


Peak Optimization Flags

C benchmarks

433.milc

470.lbm

482.sphinx3

C++ benchmarks

444.namd

447.dealII

450.soplex

453.povray

Fortran benchmarks

410.bwaves

416.gamess

434.zeusmp

437.leslie3d

459.GemsFDTD

465.tonto

Benchmarks using both Fortran and C

435.gromacs

436.cactusADM

454.calculix

481.wrf


Implicitly Included Flags

This section contains descriptions of flags that were included implicitly by other flags, but which do not have a permanent home at SPEC.


System and Other Tuning Information

Platform settings

One or more of the following settings may have been set. If so, the "General Notes" section of the report will say so; and you can read below to find out more about what these settings mean.

Linux Huge Page settings

In order to take advantage of large pages, your system must be configured to use large pages. To configure your system for huge pages perform the following steps:

Note that further information about huge pages may be found in your Linux documentation file: /usr/src/linux/Documentation/vm/hugetlbpage.txt

HUGETLB_MORECORE

Set this environment variable to "yes" to enable applications to use large pages.

LD_PRELOAD=/usr/lib64/libhugetlbfs.so

Setting this environment variable is necessary to enable applications to use large pages.

KMP_STACKSIZE

Specify stack size to be allocated for each thread.

KMP_AFFINITY

KMP_AFFINITY = < physical | logical >, starting-core-id
specifies the static mapping of user threads to physical cores. For example, if you have a system configured with 8 cores, OMP_NUM_THREADS=8 and KMP_AFFINITY=physical,0 then thread 0 will mapped to core 0, thread 1 will be mapped to core 1, and so on in a round-robin fashion.

KMP_AFFINITY = granularity=fine,scatter
The value for the environment variable KMP_AFFINITY affects how the threads from an auto-parallelized program are scheduled across processors.
Specifying granularity=fine selects the finest granularity level, causes each OpenMP thread to be bound to a single thread context.
This ensures that there is only one thread per core on cores supporting HyperThreading Technology
Specifying scatter distributes the threads as evenly as possible across the entire system.
Hence a combination of these two options, will spread the threads evenly across sockets, with one thread per physical core.

OMP_NUM_THREADS

Sets the maximum number of threads to use for OpenMP* parallel regions if no other value is specified in the application. This environment variable applies to both -openmp and -parallel (Linux and Mac OS X) or /Qopenmp and /Qparallel (Windows). Example syntax on a Linux system with 8 cores: export OMP_NUM_THREADS=8

Hardware Prefetch:

This BIOS option allows the enabling/disabling of a processor mechanism to prefetch data into the cache according to a pattern-recognition algorithm.

In some cases, setting this option to Disabled may improve performance. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Adjacent Sector Prefetch:

This BIOS option allows the enabling/disabling of a processor mechanism to fetch the adjacent cache line within an 128-byte sector that contains the data needed due to a cache line miss.

In some cases, setting this option to Disabled may improve performance. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Data Reuse Optimization (Enable/Disable):

Enabling this BIOS option reduces the frequency of L3 cache updates from L1.

This may improve performance by reducing the internal bandwidth consumed by constantly updating L1 cache lines in L3.

Since this results in more fetches to main memory, setting this option to Disabled may improve performance in some cases. Users should only disable this option after performing application benchmarking to verify improved performance in their environment.

Performance/Power Setting (Traditional/Optimized):

This BIOS option sets the turbo boost engagement after the maximum power state (P0).

If set to Traditional this will be less than 2 seconds to provide maximum performance, otherwise P0 retained for more than 2 seconds

High Bandwidth:

Enabling this option allows the chipset to defer memory transactions and process them out of order for optimal performance.

Hyper-Threading Technology:

Disabling Intel's Hyper-Threading Technology reduces the number of threads per core to 1. The default is Enabled; in this case each core provides additional resources for executing up to 2 threads in parallel.

ulimit -s <n>

Sets the stack size to n kbytes, or unlimited to allow the stack size to grow without limit.

submit= MYMASK=`printf '0x%x' $((1<<$SPECCOPYNUM))`; /usr/bin/taskset $MYMASK $command

When running multiple copies of benchmarks, the SPEC config file feature submit is sometimes used to cause individual jobs to be bound to specific processors. This specific submit command is used for Linux. The description of the elements of the command are:

Using numactl to bind processes and memory to cores

For multi-copy runs or single copy runs on systems with multiple sockets, it is advantageous to bind a process to a particular core. Otherwise, the OS may arbitrarily move your process from one core to another. This can effect performance. To help, SPEC allows the use of a "submit" command where users can specify a utility to use to bind processes. We have found the utility 'numactl' to be the best choice.

numactl runs processes with a specific NUMA scheduling or memory placement policy. The policy is set for a command and inherited by all of its children. The numactl flag "--physcpubind" specifies which core(s) to bind the process. "-l" instructs numactl to keep a process memory on the local node while "-m" specifies which node(s) to place a process memory. For full details on using numactl, please refer to your Linux documentation, 'man numactl'

submit= $[top]/mysubmit.pl $SPECCOPYNUM "$command"

On Xeon 74xx series processors, some benchmarks at peak will run n/2 copies on a system with n logical processors. The mysubmit.pl script assigns each copy in such a way that no two copies will share an L2 cache, for optimal performance. The script looks in /proc/cpuinfo to come up with the list of cores that will satisfy this requirement. The source code is shown below.

Source
******************************************************************************************************


#!/usr/bin/perl
 
use strict;
use Cwd;
 
# The order in which we want copies to be bound to cores
# Copies: 0, 1, 2, 3
# Cores:  0, 1, 3, 6
 
my $rundir        = getcwd;
 
my $copynum = shift @ARGV;

my $i;
my $j;
my $tag;
my $num;
my $core;
my $numofcores; 

my @proc;
my @cores;

open(INPUT, "/proc/cpuinfo") or
   die "can't open /proc/cpuinfo\n"; 

#open(OUTPUT, "STDOUT");

# proc[i][0] = logical processor ID
# proc[i][1] = physical processor ID
# proc[i][2] = core ID

$i = 0;
$numofcores = 0;

while(<INPUT>)
{
  chop;
 
  ($tag, $num) = split(/\s+:\s+/, $_);


  if ($tag eq "processor") {
      $proc[$i][0] = $num;
  }

  if ($tag eq "physical id") {
      $proc[$i][1] = $num;
  }

  if ($tag eq "core id") {
      $proc[$i][2] = $num;
      $i++;
      $numofcores++;
  }
}

$i = 0;
$j = 0;

for $core (0, 4, 2, 1, 5, 3) {
  while ($i < $numofcores) {
     if ($proc[$i][2] == $core) {
        $cores[$j] = $proc[$i][0];
        $j++;
     }
     $i++;
  }
  $i=0;
}

open  RUNCOMMAND, "> runcommand" or die "failed to create run file";
print RUNCOMMAND "cd $rundir\n";
print RUNCOMMAND "@ARGV\n";
close RUNCOMMAND;
system 'taskset', '-c', $cores[$copynum], 'sh', "$rundir/runcommand";


Flag description origin markings:

[user] Indicates that the flag description came from the user flags file.
[suite] Indicates that the flag description came from the suite-wide flags file.
[benchmark] Indicates that the flag description came from a per-benchmark flags file.

The flags files that were used to format this result can be browsed at
http://www.spec.org/cpu2006/flags/Intel-ic12.0-linux64-revB.20110316.html,
http://www.spec.org/cpu2006/flags/Fujitsu-Platform.20110705.html.

You can also download the XML flags sources by saving the following links:
http://www.spec.org/cpu2006/flags/Intel-ic12.0-linux64-revB.20110316.xml,
http://www.spec.org/cpu2006/flags/Fujitsu-Platform.20110705.xml.


For questions about the meanings of these flags, please contact the tester.
For other inquiries, please contact webmaster@spec.org
Copyright 2006-2014 Standard Performance Evaluation Corporation
Tested with SPEC CPU2006 v1.1.
Report generated on Wed Jul 23 21:56:10 2014 by SPEC CPU2006 flags formatter v6906.