SPEC CPU®2017 Integer Rate Result

Copyright 2017-2019 Standard Performance Evaluation Corporation

Hewlett Packard Enterprise (Test Sponsor: HPE)

ProLiant DL325 Gen10
(2.00 GHz, AMD EPYC 7702P)

SPECrate®2017_int_base = 27500

SPECrate®2017_int_energy_base = 82100

SPECrate®2017_int_peak = 29300

SPECrate®2017_int_energy_peak = 88000
CPU2017 License: 003 Test Date: Sep-2019
Test Sponsor: HPE Hardware Availability: Oct-2019
Tested by: HPE Software Availability: Aug-2019

Benchmark result graphs are available in the PDF report.

Hardware
CPU Name: AMD EPYC 7702P
  Max MHz: 3350
  Nominal: 2000
Enabled: 64 cores, 1 chip
Orderable: 1 chip
Cache L1: 32 KB I + 32 KB D on chip per core
  L2: 512 KB I+D on chip per core
  L3: 256 MB I+D on chip per chip,
16 MB shared / 4 cores
  Other: None
Memory: 256 GB (8 x 32 GB 2Rx4 PC4-2933Y-L)
Storage: 1 x HPE 480 GB SATA 6G SSD
Other: None
Software
OS: SUSE Linux Enterprise Server 15 (x86_64) SP1
Kernel 4.12.14-195-default
Compiler: C/C++/Fortran: Version 2.0.0 of AOCC
Parallel: No
Firmware: HPE BIOS Version A41 07/20/2019 released Aug-2019
File System: btrfs
System State: Run level 3 (multi-user)
Base Pointers: 64-bit
Peak Pointers: 32/64-bit
Other: jemalloc: jemalloc memory allocator library v5.2.0
Power Management: Disabled
Power
Max. Power (W): 408.86
Idle Power (W): 191.28
Min. Temperature (C): 20.00
Elevation (m): 132
Line Standard: 208 V / 60 Hz / 1 phase / 2 wires
Provisioning: Line-powered
Power Settings
Management FW: Version 1.43 of iLO5 released May 23 2019
Memory Mode: Normal
Power-Relevant Hardware
Power Supply: 1 x 800 W (non-redundant)
  Details: HPE 800W Flex Slot Titanium Hot Plug Low Halogen
Power Supply Kit (865438-B21)
Backplane: 8 SFF NVMe with optional optical drive
Other Storage: Embedded SATA Controller
Storage Model #s: P05976-B21
NICs Installed: 1 x HPE Ethernet 4-port 331i Adapter @ 1 Gb
NICs Enabled (FW/OS): 4 / 4
NICs Connected/Speed: 2 @ 1 Gb
Other HW Model #s: 7 x High Performance fans
Power Analyzer
Power Analyzer: 10.216.1.15:8888
Hardware Vendor: Yokogawa
Model: YokogawaWT210
Serial Number: 91K308562
Input Connection: GPIB via NI GIPB-USB-HS
Metrology Institute: NIST
Calibration By: TRANSCAT
Calibration Label: 5-E553M-20-1
Calibration Date: 21-May-2019
PTDaemon™ Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: SUT Power Supply 1 via neoXt NXB 20815
Current Ranges Used: 1A, 2A
Voltage Range Used: 300V
Temperature Meter
Temperature Meter: 10.216.1.15:8889
Hardware Vendor: Digi International Inc.
Model: DigiWATCHPORT_H
Serial Number: V45297862
Input Connection: USB
PTDaemon Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: 5 mm in front of SUT main intake

Base Results Table

Benchmark Copies Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECrate®2017_int_base 27500
SPECrate®2017_int_energy_base 82100
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
500.perlbench_r 64 487 209 1730 641 355 378 493 207 1740 635 353 378 484 210 1720 642 356 381
502.gcc_r 64 379 239 1450 680 382 398 379 239 1450 679 382 395 381 238 1460 676 382 395
505.mcf_r 64 322 321 1270 891 395 408 323 320 1280 887 395 409 322 321 1270 890 395 408
520.omnetpp_r 64 577 146 2270 401 394 396 586 143 2290 396 391 396 578 145 2280 399 394 397
523.xalancbmk_r 64 251 270 93.3 785 372 389 249 272 92.8 789 373 392 249 271 93.0 787 373 390
525.x264_r 64 181 618 64.4 1880 356 376 182 616 64.8 1880 356 373 182 616 64.8 1880 356 375
531.deepsjeng_r 64 305 240 1060 749 349 379 305 240 1070 748 349 375 305 240 1060 749 349 379
541.leela_r 64 467 227 1560 735 334 346 468 227 1560 733 334 347 467 227 1560 735 334 346
548.exchange2_r 64 220 761 73.6 2470 334 337 220 762 73.7 2470 335 338 220 761 73.7 2470 334 338
557.xz_r 64 444 156 1670 449 377 390 446 155 1680 448 376 390 445 155 1680 448 377 390

Peak Results Table

Benchmark Copies Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECrate®2017_int_peak 29300
SPECrate®2017_int_energy_peak 88000
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
500.perlbench_r 64 475 215 1660 666 350 376 471 216 1650 668 351 376 474 215 1660 666 351 378
502.gcc_r 64 296 307 1110 889 375 395 297 305 1110 886 374 393 296 306 1110 887 375 395
505.mcf_r 64 264 391 1030 1100 389 404 263 393 1030 1100 390 403 264 392 1030 1100 389 403
520.omnetpp_r 64 577 146 2270 401 394 396 586 143 2290 396 391 396 578 145 2280 399 394 397
523.xalancbmk_r 64 222 305 81.9 893 369 394 222 304 81.8 895 368 391 223 303 82.1 891 368 393
525.x264_r 64 178 629 63.5 1910 356 375 178 631 63.3 1920 356 374 178 628 63.5 1910 356 375
531.deepsjeng_r 64 298 246 1040 767 349 379 298 246 1040 766 349 378 318 231 1110 716 350 382
541.leela_r 64 467 227 1560 735 334 346 468 227 1560 733 334 347 467 227 1560 735 334 346
548.exchange2_r 64 220 761 73.6 2470 334 337 220 762 73.7 2470 335 338 220 761 73.7 2470 334 338
557.xz_r 64 445 155 1680 448 377 390 445 155 1670 449 376 390 445 155 1680 448 377 390

Compiler Notes

The AMD64 AOCC Compiler Suite is available at
http://developer.amd.com/amd-aocc/

Submit Notes

The config file option 'submit' was used.
'numactl' was used to bind copies to the cores.
See the configuration file for details.

Operating System Notes

'ulimit -s unlimited' was used to set environment stack size
'ulimit -l 2097152' was used to set environment locked pages in memory limit

runcpu command invoked through numactl i.e.:
numactl --interleave=all runcpu <etc>

Set dirty_ratio=8 to limit dirty cache to 8% of memory
Set swappiness=1 to swap only if necessary
Set zone_reclaim_mode=1 to free local node memory and avoid remote memory
sync then drop_caches=3 to reset caches before invoking runcpu

dirty_ratio, swappiness, zone_reclaim_mode and drop_caches were
all set using privileged echo (e.g. echo 1 > /proc/sys/vm/swappiness).

Transparent huge pages set to 'always' for this run (OS default)

Environment Variables Notes

Environment variables set by runcpu before the start of the run:
LD_LIBRARY_PATH =
     "/cpu2017/amd_rate_aocc200_rome_C_lib/64;/cpu2017/amd_rate_aocc200_rome_
     C_lib/32:"
MALLOC_CONF = "retain:true"

General Notes

Binaries were compiled on a system with 2x AMD EPYC 7601 CPU + 512GB Memory using Fedora 26

NA: The test sponsor attests, as of date of publication, that CVE-2017-5754 (Meltdown)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5753 (Spectre variant 1)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5715 (Spectre variant 2)
is mitigated in the system as tested and documented.

jemalloc: configured and built with GCC v9.1.0 in Ubuntu 19.04 with -O3 -znver2 -flto
jemalloc 5.2.0 is available here:
https://github.com/jemalloc/jemalloc/releases/download/5.2.0/jemalloc-5.2.0.tar.bz2


Submitted_by: "Bucek, James" <james.bucek@hpe.com>
Submitted: Tue Sep 17 00:02:18 EDT 2019
Submission: cpu2017-20190903-17797.sub

Platform Notes

BIOS Configuration:
 AMD SMT Option set to Disabled
 Thermal Configuration set to Optimal Cooling
 Determinism Control set to Manual
 Performance Determinism set to Power Deterministic
 Memory Patrol Scrubbing set to Disabled
 NUMA memory domains per socket set to Four memory domains per socket
 Last-Level Cache (LLC) as NUMA Node set to Enabled
 Workload Profile set to General Throughput Compute
 Minimum Processor Idle Power Core C-State set to C6 State

 Sysinfo program /cpu2017/bin/sysinfo
 Rev: r6365 of 2019-08-21 295195f888a3d7edb1e6e46a485a0011
 running on dl325gen10 Sun Sep  1 20:16:30 2019

 SUT (System Under Test) info as seen by some common utilities.
 For more information on this section, see
    https://www.spec.org/cpu2017/Docs/config.html#sysinfo

 From /proc/cpuinfo
    model name : AMD EPYC 7702P 64-Core Processor
       1  "physical id"s (chips)
       64 "processors"
    cores, siblings (Caution: counting these is hw and system dependent. The following
    excerpts from /proc/cpuinfo might not be reliable.  Use with caution.)
       cpu cores : 64
       siblings  : 64
       physical 0: cores 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
       25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
       53 54 55 56 57 58 59 60 61 62 63

 From lscpu:
      Architecture:        x86_64
      CPU op-mode(s):      32-bit, 64-bit
      Byte Order:          Little Endian
      Address sizes:       48 bits physical, 48 bits virtual
      CPU(s):              64
      On-line CPU(s) list: 0-63
      Thread(s) per core:  1
      Core(s) per socket:  64
      Socket(s):           1
      NUMA node(s):        4
      Vendor ID:           AuthenticAMD
      CPU family:          23
      Model:               49
      Model name:          AMD EPYC 7702P 64-Core Processor
      Stepping:            0
      CPU MHz:             2000.000
      CPU max MHz:         2000.0000
      CPU min MHz:         1500.0000
      BogoMIPS:            3992.33
      Virtualization:      AMD-V
      L1d cache:           32K
      L1i cache:           32K
      L2 cache:            512K
      L3 cache:            16384K
      NUMA node0 CPU(s):   0-15
      NUMA node1 CPU(s):   16-31
      NUMA node2 CPU(s):   32-47
      NUMA node3 CPU(s):   48-63
      Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
      pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm
      constant_tsc rep_good nopl xtopology nonstop_tsc cpuid extd_apicid aperfmperf pni
      pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c
      rdrand lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch
      osvw ibs skinit wdt tce topoext perfctr_core perfctr_nb bpext perfctr_l2 mwaitx cpb
      cat_l3 cdp_l3 hw_pstate ssbd ibrs ibpb stibp vmmcall fsgsbase bmi1 avx2 smep bmi2
      cqm rdt_a rdseed adx smap clflushopt clwb sha_ni xsaveopt xsavec xgetbv1 xsaves
      cqm_llc cqm_occup_llc cqm_mbm_total cqm_mbm_local clzero irperf xsaveerptr arat npt
      lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter
      pfthreshold avic v_vmsave_vmload vgif umip rdpid overflow_recov succor smca

 /proc/cpuinfo cache data
    cache size : 512 KB

 From numactl --hardware  WARNING: a numactl 'node' might or might not correspond to a
 physical chip.
   available: 4 nodes (0-3)
   node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
   node 0 size: 64290 MB
   node 0 free: 64093 MB
   node 1 cpus: 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
   node 1 size: 64507 MB
   node 1 free: 64317 MB
   node 2 cpus: 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
   node 2 size: 64507 MB
   node 2 free: 64292 MB
   node 3 cpus: 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
   node 3 size: 64465 MB
   node 3 free: 64287 MB
   node distances:
   node   0   1   2   3
     0:  10  12  12  12
     1:  12  10  12  12
     2:  12  12  10  12
     3:  12  12  12  10

 From /proc/meminfo
    MemTotal:       263958144 kB
    HugePages_Total:       0
    Hugepagesize:       2048 kB

 From /etc/*release* /etc/*version*
    os-release:
       NAME="SLES"
       VERSION="15-SP1"
       VERSION_ID="15.1"
       PRETTY_NAME="SUSE Linux Enterprise Server 15 SP1"
       ID="sles"
       ID_LIKE="suse"
       ANSI_COLOR="0;32"
       CPE_NAME="cpe:/o:suse:sles:15:sp1"

 uname -a:
    Linux dl325gen10 4.12.14-195-default #1 SMP Tue May 7 10:55:11 UTC 2019 (8fba516)
    x86_64 x86_64 x86_64 GNU/Linux

 Kernel self-reported vulnerability status:

 CVE-2018-3620 (L1 Terminal Fault):        Not affected
 Microarchitectural Data Sampling:         Not affected
 CVE-2017-5754 (Meltdown):                 Not affected
 CVE-2018-3639 (Speculative Store Bypass): Mitigation: Speculative Store Bypass disabled
                                           via prctl and seccomp
 CVE-2017-5753 (Spectre variant 1):        Mitigation: __user pointer sanitization
 CVE-2017-5715 (Spectre variant 2):        Mitigation: Full AMD retpoline, IBPB:
                                           conditional, IBRS_FW, STIBP: disabled, RSB
                                           filling

 run-level 3 Aug 31 13:56

 SPEC is set to: /cpu2017
    Filesystem     Type   Size  Used Avail Use% Mounted on
    /dev/sda2      btrfs   40G   18G   22G  45% /

 From /sys/devices/virtual/dmi/id
     BIOS:    HPE A41 07/20/2019
     Vendor:  HPE
     Product: ProLiant DL325 Gen10
     Product Family: ProLiant
     Serial:  CN781302PS

 Additional information from dmidecode follows.  WARNING: Use caution when you interpret
 this section. The 'dmidecode' program reads system data which is "intended to allow
 hardware to be accurately determined", but the intent may not be met, as there are
 frequent changes to hardware, firmware, and the "DMTF SMBIOS" standard.
   Memory:
     8x UNKNOWN NOT AVAILABLE
     8x UNKNOWN NOT AVAILABLE 32 GB 2 rank 2933

 (End of data from sysinfo program)

Power Settings Notes

PTDaemon to measure power and temperature was run on a ProLiant DL360 Gen9 as a controller
with 2x Intel Xeon E5-2660 v3 CPU and 128 GB of memory using Windows Server 2012 R2.
Power management in the OS was disabled by setting Linux CPU governor to performance for all cores:
 cpupower frequency-set -r -g performance
Power management in the BIOS was default except for any settings mentioned in BIOS Configuration.
No power management settings were set in the management firmware.
The optional optical drive was not installed.
The system was configured with 7 HPE Small Form Factor Hard Drive Blanks (666987-B21), 8 DIMM blanks
2 high performance heatsinks and baffles that fit over the high performance
heatsinks in order to produce correct airflow and cooling.
The run was started and observed through the management firmware.
The Embedded SATA controller was the HPE Smart Array S100i SR Gen10 SW RAID.

Compiler Version Notes

==============================================================================
C       | 502.gcc_r(peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: i386-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C       | 500.perlbench_r(base, peak) 502.gcc_r(base) 505.mcf_r(base, peak)
        | 525.x264_r(base, peak) 557.xz_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C       | 502.gcc_r(peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: i386-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C       | 500.perlbench_r(base, peak) 502.gcc_r(base) 505.mcf_r(base, peak)
        | 525.x264_r(base, peak) 557.xz_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++     | 523.xalancbmk_r(peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: i386-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++     | 520.omnetpp_r(base, peak) 523.xalancbmk_r(base)
        | 531.deepsjeng_r(base, peak) 541.leela_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++     | 523.xalancbmk_r(peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: i386-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++     | 520.omnetpp_r(base, peak) 523.xalancbmk_r(base)
        | 531.deepsjeng_r(base, peak) 541.leela_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
Fortran | 548.exchange2_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

Base Compiler Invocation

C benchmarks:

 clang 

C++ benchmarks:

 clang++ 

Fortran benchmarks:

 flang 

Base Portability Flags

500.perlbench_r:  -DSPEC_LINUX_X64   -DSPEC_LP64 
502.gcc_r:  -DSPEC_LP64 
505.mcf_r:  -DSPEC_LP64 
520.omnetpp_r:  -DSPEC_LP64 
523.xalancbmk_r:  -DSPEC_LINUX   -DSPEC_LP64 
525.x264_r:  -DSPEC_LP64 
531.deepsjeng_r:  -DSPEC_LP64 
541.leela_r:  -DSPEC_LP64 
548.exchange2_r:  -DSPEC_LP64 
557.xz_r:  -DSPEC_LP64 

Base Optimization Flags

C benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -z muldefs   -lmvec   -lamdlibm   -ljemalloc   -lflang 

C++ benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-suppress-fmas   -O3   -ffast-math   -march=znver2   -mllvm -loop-unswitch-threshold=200000   -mllvm -vector-library=LIBMVEC   -mllvm -unroll-threshold=100   -flv-function-specialization   -mllvm -enable-partial-unswitch   -z muldefs   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Fortran benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -ffast-math   -Wl,-mllvm -Wl,-inline-recursion=4   -Wl,-mllvm -Wl,-lsr-in-nested-loop   -Wl,-mllvm -Wl,-enable-iv-split   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -z muldefs   -mllvm -disable-indvar-simplify   -mllvm -unroll-aggressive   -mllvm -unroll-threshold=150   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Peak Compiler Invocation

C benchmarks:

 clang 

C++ benchmarks:

 clang++ 

Fortran benchmarks:

 flang 

Peak Portability Flags

500.perlbench_r:  -DSPEC_LINUX_X64   -DSPEC_LP64 
502.gcc_r:  -D_FILE_OFFSET_BITS=64 
505.mcf_r:  -DSPEC_LP64 
520.omnetpp_r:  -DSPEC_LP64 
523.xalancbmk_r:  -DSPEC_LINUX   -D_FILE_OFFSET_BITS=64 
525.x264_r:  -DSPEC_LP64 
531.deepsjeng_r:  -DSPEC_LP64 
541.leela_r:  -DSPEC_LP64 
548.exchange2_r:  -DSPEC_LP64 
557.xz_r:  -DSPEC_LP64 

Peak Optimization Flags

C benchmarks:

500.perlbench_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -fprofile-instr-generate(pass 1)   -fprofile-instr-use(pass 2)   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -lmvec   -lamdlibm   -ljemalloc   -lflang 
502.gcc_r:  -m32   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -fgnu89-inline   -ljemalloc 
505.mcf_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -lmvec   -lamdlibm   -ljemalloc   -lflang 
525.x264_r:  Same as 500.perlbench_r 
557.xz_r:  Same as 505.mcf_r 

C++ benchmarks:

520.omnetpp_r:  basepeak = yes 
523.xalancbmk_r:  -m32   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -ljemalloc 
531.deepsjeng_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -lmvec   -lamdlibm   -ljemalloc   -lflang 
541.leela_r:  basepeak = yes 

Fortran benchmarks:

548.exchange2_r:  basepeak = yes 

Peak Other Flags

C benchmarks:

502.gcc_r:  -L/sppo/dev/cpu2017/v110/amd_rate_aocc200_rome_C_lib/32 

C++ benchmarks:

523.xalancbmk_r:  -L/sppo/dev/cpu2017/v110/amd_rate_aocc200_rome_C_lib/32 

The flags files that were used to format this result can be browsed at
http://www.spec.org/cpu2017/flags/aocc200-flags-B1.html,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.html.

You can also download the XML flags sources by saving the following links:
http://www.spec.org/cpu2017/flags/aocc200-flags-B1.xml,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.xml.

PTDaemon, SPEC CPU, and SPECrate are trademarks or registered trademarks of the Standard Performance Evaluation Corporation. All other brand and product names appearing in this result are trademarks or registered trademarks of their respective holders.

For questions about this result, please contact the tester. For other inquiries, please contact info@spec.org
Copyright 2017-2019 Standard Performance Evaluation Corporation
Tested with SPEC CPU®2017 v1.1.0 on 2019-09-01 21:16:29-0400.
Report generated on 2019-09-17 16:18:01 by SPEC CPU®2017 HTML formatter v6255.
Originally published on 2019-09-17.