# Invocation command line:
# /home/hpc2021/bin/harness/runhpc -c Supermicro.cfg --reportable --tune=base --define model=mpi --define ppn=120 --threads=1 --rank=120 --size=ref --iterations=3 tiny
# output_root was not used for this run
############################################################################
#!/bin/sh
######################################################################
# Configuration file for the Intel Compilers
#
# Defines: "acctype" => "mpi", "omp", default "mpi"
#          "label" => ext base label, default "hpc"
#
#
#######################################################################
#strict_rundir_verify=0
allow_label_override=yes

%ifndef %{label}         # IF label is not set use hpc
%   define label hpc
%endif

%ifndef %{model}         # IF model is not set use mpi
%   define model mpi
%endif

teeout = yes
makeflags=-j 40

# License and tester information
license_num     = 6569
showtimer = 0
test_sponsor    = Supermicro
tester          = Supermicro

#include: Example_SUT.inc
#  ----- Begin inclusion of 'Example_SUT.inc'
############################################################################
######################################################
# Example configuration information for a
# system under test (SUT) Section
######################################################
# General SUT info
system_vendor      = Supermicro
system_name        = SuperServer SYS-741GE-TNRT (Intel Xeon Platinum 8490H)
interconnect_fs_label = N/A
hw_avail           = Jan-2023
sw_avail           = Dec-2022
prepared_by = Supermicro

# Computation node info
# [Node_Description: Hardware]
node_compute_syslbl = SuperServer SYS-741GE-TNRT
node_compute_order = 1
node_compute_count = 1
node_compute_purpose = Compute
node_compute_hw_vendor = Supermicro
node_compute_hw_model = SuperServer SYS-741GE-TNRT
node_compute_hw_cpu_name = Intel Xeon Platinum 8490H
node_compute_hw_ncpuorder = 1, 2 chips
node_compute_hw_nchips = 2
node_compute_hw_ncores = 120
node_compute_hw_ncoresperchip = 60
node_compute_hw_nthreadspercore = 2
node_compute_hw_cpu_char = Intel Turbo Boost Technology up to 3.5 GHz
node_compute_hw_cpu_mhz = 1900
node_compute_hw_pcache = 32 KB I + 48 KB D on chip per core
node_compute_hw_scache = 2 MB I+D on chip per core
node_compute_hw_tcache   = 112.5 MB I+D on chip per chip
node_compute_hw_ocache = None
node_compute_hw_memory = 512 GB (16 x 32 GB 2Rx8 PC5-4800B-R)
node_compute_hw_disk = 1 x 256 GB Apacer M.2 NVMe SSD
node_compute_hw_other = None

#[Node_Description: Accelerator]

#[Node_Description: Software]
node_compute_hw_adapter_fs_model = None
node_compute_hw_adapter_fs_count = 0
node_compute_hw_adapter_fs_slot_type = None
node_compute_hw_adapter_fs_data_rate = None
node_compute_hw_adapter_fs_ports_used = 0
node_compute_hw_adapter_fs_interconnect = None
node_compute_hw_adapter_fs_driver = None
node_compute_hw_adapter_fs_firmware = None
node_compute_sw_os000 = SUSE Linux Enterprise Server 15 SP4
node_compute_sw_os001 = Kernel 5.14.21-150400.22-default
node_compute_sw_localfile = xfs
node_compute_sw_sharedfile = None
node_compute_sw_state = Multi-user, run level 3
node_compute_sw_other = None

#[Fileserver]

#[Interconnect]
interconnect_fs_syslbl = N/A
interconnect_fs_order = 0
interconnect_fs_purpose = N/A
interconnect_fs_hw_vendor = N/A
interconnect_fs_hw_model = N/A
interconnect_fs_hw_switch_fs_model   = None
interconnect_fs_hw_switch_fs_count = 0
interconnect_fs_hw_switch_fs_ports = 0
interconnect_fs_hw_topo = N/A
interconnect_fs_hw_switch_fs_data_rate = N/A
interconnect_fs_hw_switch_fs_firmware = N/A

#######################################################################
# End of SUT section
# If this config file were to be applied to several SUTs, edits would
# be needed only ABOVE this point.
######################################################################
# ---- End inclusion of '/home/hpc2021/config/Example_SUT.inc'

sw_compiler000   = C/C++/Fortran: Version 2023.0.0 of
sw_compiler001   = Intel oneAPI Compiler
sw_mpi_library000 = Intel MPI Library for Linux* OS,
sw_mpi_library000 = Intel MPI Library for Linux* OS, Version 2021.8.0
sw_mpi_library001 = Build 20221129
sw_mpi_other = None
sw_other = None

notes_000 = MPI startup command:
notes_005 =   mpirun command (mpiexec.hydra) was used to start MPI jobs.

label         = %{label}_%{model}
tune          = base
output_format = text
use_submit_for_speed = 1
flagsurl000=http://www.spec.org/hpc2021/flags/Intel_compiler_flags.2023-02-09.xml

# Compiler Settings
default:
AR           = ar
ARFLAGS      = cr
CXX          = mpiicpc -cxx=icpx
CC           = mpiicc -cc=icx
FC           = mpiifort -fc=ifx
system_class = Homogenous

# Compiler Version Flags
CC_VERSION_OPTION  = --version
CXX_VERSION_OPTION = --version
FC_VERSION_OPTION  = --version

default=base=default:
OPTIMIZE      = -Ofast -ipo -xCORE-AVX512 -mprefer-vector-width=512
COPTIMIZE     = -ansi-alias
CXXOPTIMIZE   = -ansi-alias
FOPTIMIZE     = -nostandard-realloc-lhs -align array64byte
PORTABILITY   = -lstdc++
mpicmd = mpiexec.hydra -bootstrap ssh -genv OMP_NUM_THREADS $threads -np $ranks -ppn $ranks $command
submit = $mpicmd

#default=base=default:
#    ranks   = %{RANKS}
#    threads = %{THREADS}

%if %{model} eq 'mpi'
  pmodel=MPI
%endif

# OpenACC flags
%if %{model} eq 'acc'
  pmodel=ACC
  OPTIMIZE += -fopenacc -foffload=-lm
%endif

# OpenMP (CPU) flags
%if %{model} eq 'omp'
  pmodel=OMP
  OPTIMIZE += -fiopenmp
%endif

# OpenMP Targeting host flags
%if %{model} eq 'tgt'
  pmodel=TGT
  OPTIMIZE += -fopenmp
%endif

# OpenMP Targeting Nvidia GPU flags
%if %{model} eq 'tgtnv'
  pmodel=TGT
  OPTIMIZE += -fopenmp -fopenmp-targets=nvptx64-nvidia-cuda
%endif

# No peak flags set, so make peak use the same flags as base
default=peak=default:
basepeak=1

513.soma_t=base,peak:
    PORTABILITY+=-DSPEC_NO_VAR_ARRAY_REDUCE

528.pot3d_t=base,peak:
#	PORTABILITY+=-DSPEC_NO_REORDER
	OPTIMIZE+=-Wno-incompatible-function-pointer-types